Korg M3 Manuel d'utilisateur télécharger pdf (Page 141)

Global settings Assigning MIDI CC#s to KARMA, X–Y, and Pad controllers

133

Quick Start

Introduction

SetupProgram

Combination

Sequencer

SamplingGlobalMediaEffectKARMA

Drum Track

Other

Appendices

Switch portamento on/off

Control the sostenuto effect

Turn the soft pedal effect on/off

Turn the damper effect on/off

Select programs or combinations (up/down)

Value Inc/Dec

Start/stop the sequencer

Punch-in/out on the sequencer

Cue list repeat

Tap tempo

Control of KARMA function

Switch the drum track on/off

Switch X–Y mode or X–Y motion on/off

The functions of controllers such as the joystick or

ribbon controller (See “Foot Switch Assign” on

page 371 of the Parameter Guide)

Assignable Pedal

You can specify the function that will be performed by

an assignable pedal (the optional XVP-10 Expression/

Volume pedal or EXP-2 foot controller) connected to

the ASSIGNABLE PEDAL jack.

• This is set by “Foot Pedal Assign.”

You can choose from the following functions.

Master volume

Alternate modulation source

Effect dynamic modulation source

Portamento pitch change speed

Volume (expression)

The pan following an insert effect

Pan

Volume

Send levels to the master effects

Duplicate the function of another controller, such as

the joystick or ribbon (See “Foot Pedal Assign” on

page 371 of the Parameter Guide)

Note: You can use this as a source for alternate

modulation or effect dynamic modulation, and use it

to control program parameters or effect parameters. In

this case, set Foot Switch Assign to Foot SW (CC#82),

and Foot Pedal Assign to Foot Pedal (CC#04).

Assigning MIDI CC#s to

KARMA, X–Y, and Pad

controllers

In the Global P2: Controllers– MIDI CC# Assign page

you can assign control change messages to the

KARMA switches and sliders, pads 1–8, and the X-axis

and Y-axis of X–Y control. Pads 1–8 can be assigned

either control change messages or note numbers. You

can assign control change messages or note numbers to

pads 1–8.

Normally you will use the default settings. To restore

the default settings, execute the Reset Controller

MIDI Assign menu command and choose Default

Setting.

Creating user scales

Creating an original scale, and

assigning it to a Program

On the User Scale page, you can create your own

original scales. These include sixteen different User

Octave Scales, in which the pitch of each note of the

octave is repeated for all octaves, and one User All

Note Scale, in which the pitch of each of the 128 notes

can be speciﬁed independently.

By adjusting the pitch of each key in the range of ±99

cents, you can raise or lower it by approximately one

semitone relative to the normal pitch.

The user scales you create here can be used by

specifying the scale for a program, for each timbre of a

combination, or for each track of a song.

You can choose these scales from the following pages.

Here is how to set the scale type for each timbre in

Sequencer mode.

1. Create a user octave scale or a user all notes scale.

If you’re creating a user octave scale, use User Octave

Scale Select to select the scale you want to create.

2. Select a key, and use the VALUE controllers to

adjust the pitch. The range of ±99 raises or lowers

the pitch approximately one semitone above or

below the standard pitch.

Note: You can also select a key by holding down the

ENTER switch and playing the desired note on the

keyboard.

Note: You can copy one of the preset scales and edit it

to create an original scale. To do so, use the menu

command Copy Scale.

Mode Page

Program P1– Key Zone/Scale: Scale

Combination

P2– Other T01–08, T09–16: Scale, Use

Program’s Scale

Sequencer

P3– Other T01–08, T09–16: Scale, Use

Program’s Scale

1 2 ... 136 137 138 139 140 141 142 143 144 145 146 ... 236 237

Commentaires sur ces manuels

Pas de commentaire

Korg M3 Manuel d'utilisateur Page 141

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Korg M3