Korg M3 Manuel d'utilisateur télécharger pdf (Page 165)

Routing effect settings Using effects in Combinations and Songs

157

Quick Start

Introduction

SetupProgram

Combination

Sequencer

SamplingGlobalMediaEffectKARMA

Drum Track

Other

Appendices

The procedure is the same as when selecting an

insertion effect (see step 7).

Note: You can select a double-size effect only for MFX1.

(See “Double-size effects” on page 156)

15.Press the On/Off button to turn on the master

effect.

Each time you press the button, the master effect will

be switched on/off. When Off, the output of the master

effect will be muted.

16.Use “Return 1” and “Return 2” to adjust the

output levels of the master effects.

Note: For each effect, the Wet value of the Wet/Dry

parameter is the output level at the effect. The return

value is multiplied with this (“Return” = 127 will be

x1.0) to determine the actual output level of the master

effect.

17.Select the MFX1 and MFX2 pages, and set the

parameters for each selected effect.

For details on the “Program Effects settings” step 11.

Total Effect

18.If you use “Bus (IFX/Output) Select” to choose L/R

as the oscillator output, or if you set the post-IFX

Bus Select to L/R, the signal will be input to the

total effect.

The output from the master effects is input to the total

effect via the “Return 1” and “Return 2” settings of the

Prog P9: MFX/TFX– Routing page.

After being processed through the total effect, the

signal is output from the AUDIO OUTPUT (MAIN) L/

MONO and R outputs.

19.Access the Prog P9: MFX/TFX– Routing page.

20.Choose the desired total effect for TFX. The

procedure is the same as when selecting an insert

effect. (See step 7)

You can’t use a double-size effect as the total effect.

(See “Double-size effects” on page 156 of the

Parameter Guide)

21.Press the On/Off button to turn the total effect on.

The total effect will be switched on/off each time you

press the button. If this is Off, the result will be the

same as if 000: No Effect is selected. The input sound

will be output without change.

22.Access the TFX page, and edit the parameters of

each effect to adjust the ﬁnal sound as desired.

For details on the “Program Effects settings” step 11.

Using effects in Combinations

and Songs

In Combination, and Sequencer modes, you can

specify the routing of each timbre/track to the insert

effects, master effects and total effect. These settings

are made in the same way in each of these modes. We

will be using the example of Combination mode in our

explanation here.

Routing

1. Access the Combi P8–1: IFX– Routing1 T01–08

page.

2. Use “Bus Select (IFX/Indiv.Out Assign)” to specify

the bus to which each timbre will be output.

Choose IFX1 if you want to send the output of a

timbre to insert effect 1.

The routing, insert effects, and chain settings are

shown graphically in the upper part of the page. In this

example, T01 (timbre 1) uses IFX1 and 2. T02 uses IFX2,

T03 uses IFX3 and 4, T02 and T05 use IFX4, and T06

and T07 use IFX5.

3. Use Send1 and Send2 to specify the send level of

each timbre to the master effects.

This can be set only if Bus Select (IFX/Indiv.Out

Assign) is set to L/R or Off.

Note: The actual send level is determined by

multiplying this by the Send 1 or Send 2 settings for

oscillators 1 and 2 within the program selected by the

timbre. If the program parameter Send 1 or Send 2 is

set to 0, the resulting level will still be 0 even if you

raise this send level.

If Bus Select (IFX/Indiv.Out Assign) is set to IFX1–5,

the send levels to the master effects are set by Send1

and Send2 (Insert FX Setup page) following the insert

effects.

4. Access the Combi P8–2: IFX– Routing2 page.

Bus Select (IFX/Indiv. Out Assign) is the same as in

the Routing 1 page. You can set it from either page.

FX Control Bus sends the output of the timbre to an FX

Control bus. Use this when you want the audio input

to an effect to be controlled by another sound. There

are two FX Control buses, which gives you a great deal

of freedom for controlling effects freely. (See “FX

Control Buses” on page 423 of the Parameter Guide)

AUX Bus sends the output of the timbre to a AUX bus.

In the P0: Play– Sampling/Audio In page, you can set

1 2 ... 160 161 162 163 164 165 166 167 168 169 170 ... 236 237

Korg M3 Manuel d'utilisateur Page 165

Commentaires sur ces manuels

Korg M3 Manuel d'utilisateur Page 165

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Korg M3