Korg Triton Studio Manuel d'utilisateur télécharger pdf (Page 109)

Metronome Precount [Off, 4, 8, 3, 6]

Speciﬁes whether the metronome will sound a countdown

when you use “Trigger” Sampling START SW to begin

sampling.

This can be set only if “Trigger” is set to Sampling START

SW.

Off: Sampling will begin immediately when you press the

SAMPLING [START/STOP] key from recording-standby

mode.

4, 8, 3, 6: When you press the SAMPLING [START/STOP]

key from recording-standby mode, the metronome will

count the speciﬁed number of beats at the “ (Tempo)”

tempo, and then sampling will begin. If you set this to 4,

sampling will begin on the count of 0 after a pre-count of 4–

3–2–1–0.

The output destination and level of the metronome

sound are speciﬁed by Metronome Setup (0–3c).

Resample [Manual, Auto]

Speciﬁes how resampling will occur.

This can be set only if “Trigger” is set to Sampling START

SW.

The process of sampling a sample (or samples) is called “res-

ampling.”

You can apply effects to a sample and then resample it, or

resample a performance of samples that you play.

Manual: This is the normal method. Use this when you want

to sample an external input sound. If a sample is already

assigned, the sample assigned for playing from the keyboard

will be resampled together with the external input sound.

Auto: The sample assigned to the index will be resampled

automatically. Use this when you want to apply an effect to

an existung sample and resample the results.

1 Set “Key” to the keyboard location where the sample you

that you want to resample is assigned.

Sampling will not be possible if you specify a key to

which a sample has not been assigned.

2 If you want to apply an effect, go to the P8: Routing page

and set “BUS (IFX) Select” (8–1b) to IFX1–5 to specify

the insert effect that you want to use. Then set “Source

BUS” (0–2b) to L/R.

3 Press the SAMPLING [REC] key to enter record-ready

mode.

4 When you press the SAMPLING [START/STOP] key, the

current sample will play back automatically, and the res-

ampling will begin. If you play the keyboard at this time,

the sound you play will be resampled together with the

source sample.

5 When the sample assigned to the “Key” has played back

for its full length, resampling will end automatically.

Alternatively, you can stop resampling by pressing the

SAMPLING [START/STOP] key once again.

When resampling ends, the “BUS (IFX) Select” (8–1b)

setting will automatically be reset to L/R. Please be

aware of this if you want to resample once again.

The parameters of the newly created sample will be

automatically set the same as the source sample when

played back.

Key [C–1...G9]

When “Resample” is set to Auto, this speciﬁes the note to

which the sample to be resampled is assigned.

This can be set only if “Trigger” is set to Sampling START

SW.

(☞For the resampling procedure, refer to “Resample”

Auto.)

Level [–63dB ... 0dB]

When sampling with “Trigger” set to Threshold, this speci-

ﬁes the level at which sampling will begin. This can be set

only when “Trigger” is set to Threshold. (☞Refer to step

of the “Trigger” Threshold procedure.)

 (Tempo) [040...240]

This sets the tempo of the count-down when “Metronome

Precount” is used.

The tempo speciﬁed here will also be used when the LFO or

delay time of the insert effect is controlled by the BPM/

MIDI SYNC function during sampling (☞p.248). This can

also be set by the [TEMPO] knob.

Pre Trigger REC [000...500ms]

If you want a portion of sound immediately before the start

of sampling to be included in the recorded sample, set this

parameter to specify the length.

When sampling with “Trigger” Threshold, sampling will

start when the input signal exceeds the “Level” threshold

level. However if the “Level” setting causes a portion of the

attack to be lost, you can set the “Pre Trigger REC” parame-

ter to capture the early attack as well.

When sampling with “Trigger” Sampling START SW, it is

best to use “Metronome Precount” so that the instrumental

performance etc. is sampled in tempo. If the performance is

ahead of the tempo, this Pre Trigger REC parameter lets you

sample without losing any of it.

If you increase this setting, you will always be sampling

an unneeded portion ahead of the desired sample. Nor-

mally you should set this to 000 ms, and specify the

minimum required length when necessary.

ADC OVERLOAD !!

The “ADC OVERLOAD !!” indication will appear if the sig-

nal level from AUDIO INPUT 1 and 2 exceeds the maximum

level. If this occurs, adjust the [LEVEL] knob or the output

level of the external sound source (☞“Recording Level [dB]”

0–1d).

0–2c: Recording Level [dB]

Recording Level [dB] [–inf, –72.0... 0.0...+18.0]

☞ 0–1d

0–3: Preference

0–1

0–3a

0–3b

0–3c

1 2 ... 104 105 106 107 108 109 110 111 112 113 114 ... 321 322

Commentaires sur ces manuels

Pas de commentaire

Korg Triton Studio Manuel d'utilisateur Page 109

Commentaires sur ces manuels

Produits connexes et manuels pour Les dispositifs de saisie Korg Triton Studio