Korg Triton Studio Manuel d'utilisateur télécharger pdf (Page 116)

105

Sampling

P1 P2 P3 P4 P5 P8

5 In “Curve,” specify the way in which the volume will

change.

Linear: The volume will change linearly. For normal

fade-in or fade-out, select Linear.

Power: The volume will change non-linearly. When you

use “Mix” (1–1F) to combine a faded-in waveform with a

different faded-out waveform (i.e., crossfade), using a

Linear fade-in/out may produce an impression that the

volume has dropped in the middle of the curve. In such

cases, use Power to perform the fade-in/out.

6 In “Save to No.,” specify the save destination sample

number. By default, an unused sample number will be

selected.

The sample number cannot be speciﬁed if “Overwrite” is

checked (☞p.101).

For stereo samples, use “Save to No.(L)” and

“(R)” to specify the save-destination of the L and R chan-

nels.

7 To execute the Volume Ramp command, press the OK

button. To cancel, press the Cancel button.

1–1K: Rate Convert

This command lowers the sampling rate (frequency) of the

sampled data by 2/3, 1/2, 1/3, 1/4, or 1/6. The sampling

frequency of input is ﬁxed at 48 kHz, but you can use this

command to create “down-sampling” effects. The sample

data is thinned to convert it into sample data of a lower sam-

pling frequency.

The “Rate Convert” command is always executed on all

waveform data of the selected sample, regardless of the

“Edit Range Start” and “Edit Range End” settings.

1 Use “Sample Select” (1–1b) to select the sample that you

wish to edit.

2 Select “Rate Convert” to access the dialog box.

3 The sampling rate of the selected sample is shown at the

right of “Rate.” At the right of the “->” you can select the

desired amount of the sampling rate conversion: 2/3, 1/2,

1/3, 1/4 1/6. The sampling rate following conversion will

be displayed in Hz.

4 In “Save to No.,” specify the save destination sample

number. By default, an unused sample number will be

selected.

The sample number cannot be speciﬁed if “Overwrite” is

checked (☞p.101).

For stereo samples, use “Save to No.(L)” and

“(R)” to specify the save-destination of the L and R chan-

nels.

5 To execute the Insert Zero command, press the OK but-

ton. To cancel, press the Cancel button.

This command cannot be executed on a sample whose

sampling rate is 11.025 kHz or less.

Stereo samples must have the same sampling rate.

Although it is possible to select mono multisamples for

-L and -R and convert their sampling rate separately,

they can no longer be handled as a stereo sample in this

case.

1–1L: Reverse

This command reverses the sample data (i.e., exchanges the

beginning and end).

The “Reverse” command is always executed on all wave-

form data of the selected sample, regardless of the “Edit

Range Start” and “Edit Range End” settings.

1 Use “Sample Select” (1–1b) to select the sample that you

wish to edit.

2 Select “Reverse” to access the dialog box.

3 In “Save to No.,” specify the save destination sample

number. By default, an unused sample number will be

selected.

The sample number cannot be speciﬁed if “Overwrite” is

checked (☞p.101).

For stereo samples, use “Save to No.(L)” and

“(R)” to specify the save-destination of the L and R chan-

nels.

4 To execute the Reverse command, press the OK button.

To cancel, press the Cancel button.

When you execute this command, all of the sample data

will be rewritten to reverse its direction. The P2: Loop

Edit also contains a “Rev” (2–1c) command, which sim-

ply reverses the playback direction without affecting

the sample data itself.

1–1M: Grid

This command displays a grid in the “sample waveform dis-

play.”

When you set the Grid to On and execute this command,

vertical dotted lines will appear in the “sample waveform

display” according to the speciﬁed resolution (“Resolution”)

and tempo (“Grid” 1–1c, 2–1c). Use the grid when you wish

to cut the sample data or determine waveform starting loca-

tions based on BPM values or beats.

The vertical dotted lines will be shown starting at the

“Start” (when Loop is off) or “Loop Start” (when Loop

is on) (P2: Loop Edit) addresses, and are calculated

according to the playback when the sample is played by

the currently selected key (displayed in gray) (☞“Key-

board & Index” 0–1a).

1 Use “Sample Select” (1–1b) to select a sample.

2 Select “Grid” to access the dialog box.

3 Use the On/Off Radio buttons to switch the grid on or

off.

0–1A

0–1B

0–1C

0–1D

0–1E

0–1G

0–1H

0–1I

0–1J

0–1F

1–1M

1–1N

1 2 ... 111 112 113 114 115 116 117 118 119 120 121 ... 321 322

Commentaires sur ces manuels

Pas de commentaire

Korg Triton Studio Manuel d'utilisateur Page 116

Commentaires sur ces manuels

Produits connexes et manuels pour Les dispositifs de saisie Korg Triton Studio