Korg Triton Studio Manuel d'utilisateur télécharger pdf (Page 84)

Sequencer

P1 P2 P3 P4 P5 P6 P7 P8 P9

5–1L: Create Ctrl Data (Create Control Data)

This command gradually varies continuous-type data (e.g.,

control change, after touch, pitch bend, tempo) in the speci-

ﬁed area.

1 In “Track Select,” select the track on which you wish to

perform the Create Control Data command.

If you wish to modify tempo data, select Master Track as

the track. In this case, the step

4 item “Kind” will be set

to “Te mp o.”

2 Select “Create Ctrl Data” to access the dialog box.

3 Specify the range into which the control data will be

inserted.

In “From Measure” and “To End of Measure” specify

the measures, and in “Beat.Tick” specify the beat and

clock. (By default, “From Measure” and “To End of Mea-

sure” will be set to the range you speciﬁed in the Track

Edit page.)

4 “Kind” to the type of musical data (event) that you wish

to create.

Control change: Control change data will be inserted. In

this case, use “#” to specify the control change number.

After Touch: Aftertouch data will be inserted.

Pitch Bend: Pitch bend data will be inserted.

5 In “Start Value,” select the starting value of the control

data. In “End Value,” select the ending value of the con-

trol data. By default, the “Start Value” will be set to the

value of the existing data at the start location. If you wish

to create control data that changes smoothly from the

starting location, you can leave the “Start Value”

unchanged, and set only the “End Value.”

6 To execute the Create Control Data command, press the

OK button. To cancel, press the Cancel button.

When you execute Create Control Data, a large amount

of sequencer memory will be consumed. For this reason

it may not be possible to execute this command if there

is a limited amount of memory remaining. In such

cases, ﬁrst use “Quantize” (5–1N) to quantize the data

and remove unnecessary control data. Alternatively,

you could quantize the data that was inserted by the

Create Control Data command.

5–1M: Erase Ctrl Data (Erase Control Data)

This command erases data such as control changes, after

touch, pitch bend, or tempo in the speciﬁed range.

1 In “Track Select,” select the track from which you wish

to erase control data.

If you wish to erase tempo data, select Master Track. In

this case, the “Kind” item in step

4 will be Te mp o.

2 Select “Erase Ctrl Data” to access the dialog box.

3 Specify the range from which you wish to erase control

data.

In “From Measure” to “To End of Measure” specify the

measures, and in “Beat.Tick” specify the beat and clock.

(By default, “From Measure” and “To End of Measure”

will be the range that was speciﬁed in the Track Edit

page.)

4 “Kind” to the type of musical data (event) that you wish

to erase.

Control change: Control change data will be erased. In

this case, use “#” to specify the control change number.

After Touch: Aftertouch data will be erased.

Pitch Bend: Pitch bend data will be erased.

5 To execute the Erase Control Data command, press the

OK button. To cancel, press the Cancel button.

If you wish to erase all control change data from speci-

ﬁed measures, you can also use “Erase Measure” (5–1F)

and set “Kind” to Control Change. However, this Erase

Control Data command allows you to specify the range

using “Beat.Tick,” and also to erase only speciﬁc types

of control change data.

5–1N: Quantize

This command corrects the timing of musical data that

already exists in the sequencer. When you execute the Quan-

tize operation, the musical data will be affected as follows:

• When you execute Quantize on note data, the timing of

the note-on will be corrected, but the length (duration of

the note) will not be affected.

• If the Quantize resolution is set to Hi, the timing will be

adjusted to units of the base resolution (/192), so note

data will not be affected. However, continuous

controller data such as joystick or after touch which

occupies a large amount of memory will be processed so

that two or more data events of an identical type existing

at a single interval of the timing resolution will be

combined into a single event, thus conserving memory.

Similarly, two or more data events of an identical type

existing at the identical timing will be combined into one,

also conserving memory.

1 In “Track Select,” specify the track.

2 Select “Quantize” to access the dialog box.

3 Specify the range that will be quantized.

Location

3:00 3:24 3:48 3:72 4:00 4:24 4:48

After touch

127

100

Previous data

Start location End location

End Value

Start Value

default value

Example: The controller is aftertouch. Starting location is 3:48, ending location is 4:24,

and end value is set to 100. This will cause the aftertouch value to begin

changing from 3:48, and reach a value of 100 at 4:24.

1 2 ... 79 80 81 82 83 84 85 86 87 88 89 ... 321 322

Commentaires sur ces manuels

Pas de commentaire

Korg Triton Studio Manuel d'utilisateur Page 84

Commentaires sur ces manuels

Produits connexes et manuels pour Les dispositifs de saisie Korg Triton Studio