Korg Triton Studio Manuel d'utilisateur télécharger pdf (Page 301)

290

Installing a DRAM SIMM

Before you perform the installation, be sure to read the fore-

going section “Safety precautions” and “Please note when

installing an option board/memory.”

A maximum of three memory SIMMs can be installed.

A DRAM SIMM will function correctly when installed

in any slot.

For ease of installation, we recommend that you ﬁrst

use the slot that is furthest from yourself.

If you wish to use three 32 Mbytes DRAM SIMMs, you

will need to remove the factory-installed 16 Mbytes

DRAM SIMM as explained in “Removing an DRAM

SIMM.”

You must leave the AC power cable disconnected until

you ﬁnish the entire process of removing the lid, install-

ing the option board or memory, and reattaching the

lid.

1 Remove the EXB-PCM/sample memory (RAM) slot

cover as described in “Installing an EXB-PCM board”

steps

1 and 2.

2 Have the DRAM SIMM at hand.

3 Verify the location of the slot into which you will install

the DRAM SIMM module.

The three slots furthest away from yourself are for

DRAM SIMM modules. (The seven slots closest to your-

self are for EXB-PCM modules.) When the TRITON STU-

DIO is shipped from the factory, a 16 Mbytes DRAM

SIMM is installed in the furthest slot. If you want to add

one or two additional memory modules, install them in

the vacant slots. If you want to install three memory

modules, remove the factory-installed DRAM SIMM as

described in “Removing a DRAM SIMM,” and use all

three of the slots.

The end with the notch is 1 PIN. Align the 1 PIN mark

( ) of the slot with the 1 PIN marking on the EXB-PCM.

The DRAM SIMM slots and the EXB-PCM slots are

shaped identically. Be careful not to install a board in

the wrong slot.

4 At a slant, press the DRAM SIMM ﬁrmly all the way into

the slot, and raise it to the vertical position until the

catches of the slot click into the locking holes of the

DRAM SIMM. When doing so, pressing the catches of the

slot apart to the left and right will help the board go in

smoothly.

5 Reversing the procedure by which you opened the EXB-

PCM/sample memory (RAM) slot cover, reattach the

cover and fasten it with the screw.

6 When all steps have been completed, turn on the power

and make sure that the DRAM SIMM has been installed

correctly. (“Checking after installation” ☞p.287)

Removing an DRAM SIMM

• Spread the catches of the slot apart to the left and right,

and (after removing the stoppers from the catches) tilt

the DRAM SIMM and pull it out.

If you wish to remove the rear DRAM SIMM board, you

must ﬁrst remove the forward DRAM SIMM.

When you spread the catches of the slot apart, the

DRAM SIMM may pop out vigorously and fall into an

opening (inside the instrument). Please be careful.

Notch

Sample

memory

(RAM) slots

EXB-PCM

slots

Catches

Locking

hole

Locking

hole

Rear side of DRAM SIMM

Front

Catch

DRAM SIMM

1. Firmly press in at an angle.

2. Tilt up vertically.

Front

Catch

DRAM SIMM

1 2 ... 296 297 298 299 300 301 302 303 304 305 306 ... 321 322

Commentaires sur ces manuels

Pas de commentaire

Korg Triton Studio Manuel d'utilisateur Page 301

Commentaires sur ces manuels

Produits connexes et manuels pour Les dispositifs de saisie Korg Triton Studio